Landoll PT Series 10 through 20 Transport Pulverizer Manual do Utilizador

®189rev0713

1-6 9J017INTRODUCTION AND SAFETY INFORMATIONPage Intentionally Blank

2-1Chapter 2AssemblyCAUTIONThe intent of this chapter is to provide instruction, allowing you to safely and correctly assemble your Brillion product.

2-2 9J017ASSEMBLY3. If a center bracket is included with the machine, it must be installed next. Start by clamping the center brackets between the pai

ASSEMBLY2-3End Brackets Installation:1. Start with the right hand end plate and the two angle members required, See Figure 2-3.2. Bolt the three piece

2-4 9J017ASSEMBLYWheel And Axle Assemblies (Wheel Gangs) InstallationIMPORTANTKeep the Wheel Gang Assemblies in close alignment during the assembly pr

ASSEMBLY2-5Figure 2-5: Wheel and Axle Installation - 2 of 46. If the wheel gang has female hardware, slide the wheel gang end-wise, toward the center

2-6 9J017ASSEMBLY8. Position and block up the center frame against the end of the drawbar, lining up the holes in the drawbar with the center frame mo

ASSEMBLY2-7Drawbar Hitch Installation1. Mount the flat spring to the bottom of the drawbar with 3/8-16 x 1” long Screws, 3/8” Lockwashers and 3/8” Nut

2-8 9J017ASSEMBLYDrawbar Brace InstallationNOTEBoth braces and ends are identical. 1. Using Grade 5, 1-8 x 5 1/2” Screws and 1” Flat Washers and Nuts,

ASSEMBLY2-9Wheel Arms to Center Frame Installation1. Using 5/8-11 x 5 1/2” x 6 11/16” center U-bolts, 5/8” Lockwashers and Nut, attach the wheel arms

2-10 9J017ASSEMBLYHydraulic Cylinder InstallationAvoid the hazard by relieving pressure before disconnecting hydraulic lines.On most tractors this can

ASSEMBLY2-11Hydraulic Hose Installation:Figure 2-12: Hydraulic Hose Installation1. Turn the O-Ring end of Restrictor into the cylinder port. Install E

2-12 9J017ASSEMBLYPT Series 10’-20’ Models LED Lamp and Harness InstallationNOTEUnless otherwise noted the following installation instructions apply t

ASSEMBLY2-13Figure 2-13: LED SchematicAmber LED LampLED WarningLights HarnessFlasher ControlModule7Pin/4PinWP HarnessRed LED LampAmber LED LampWhen pl

2-14 9J017ASSEMBLYFigure 2-14: PT-Series 10’-20’ LED Warning Lights Installation DimensionsFigure 2-15: LED Lamp Adjustment &/5HG/DPS 5

ASSEMBLY2-15Figure 2-16: LED Modules and BracketsLED Module&Brkt1Module BracketScrew, 1/4-20 X 1-1/2Locknut, 1/4-20Light ModuleScrew, 1/4-20 X 1-1

2-16 9J017ASSEMBLY Figure 2-17: PT 10’ LED Warning Lights Installation PB LED LIGHT 10'LightBracketLightShieldDecalPlateModuleBracketLocknut,1/4-

ASSEMBLY2-17Figure 2-18: PT 12’-16’ LED Warning Lights InstallationPB LED LIGHT 12-16'7 Pin HarnessModuleBracketSMVU-Bolt, 5/8-11Screw, 5/16-18 X

2-18 9J017ASSEMBLYFigure 2-19: PT 17’-20’ LED Warning Lights InstallationPB LED LIGHT 17-20'7 Pin HarnessLamp HarnessDecal PlateLight BracketScre

ASSEMBLY2-19P Series10’-16’ Models LED Lamp and Harness InstallationNOTEUnless otherwise noted the following installation instructions apply to all P

iTable of Contents1 Introduction and Safety InformationIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-20 9J017ASSEMBLYFigure 2-20: P-Series 10’-16’ LED Warning Lights Installation Dimensions&/5HG/DPS5HG/DPS$PEHU/D

ASSEMBLY2-21Figure 2-21: P Series 10’-16’ LED Warning Lights InstallationPB LED LIGHT P1016LightBracketLight ShieldDecalPlateLocknut,1/4-20Screw,1/4-2

2-22 9J017ASSEMBLYScraper Assembly Procedure for the Optional 8J001 Wheel1. Attach scraper brackets to frame tube of pulverizer. See Figure 2-22.IMPOR

ASSEMBLY2-23Scraper Assembly Procedure for the Optional 3J619 and 8C988 Wheels1. Attach the scraper brackets. (three required for the 4” x 6” frame tu

2-24 9J017ASSEMBLYTable provided for general use.NOTES:

3-1Chapter 3OperationOperation of the Transport PulverizerThis chapter will cover the basic operation and procedures for the Landoll Brillion Transpor

3-2 9J017OPERATIONParking the Transport PulverizerThe best way to park the pulverizer is to place the machine in its desired location. Once there, rem

4-1Chapter 4Preventative MaintenanceFastenersIMPORTANTBefore operating your Brillion machine, check all hardware for tightness. Use the Tightening Tor

4-2 9J017PREVENTATIVE MAINTENANCETiresThe wheels furnished with 10’ - 12’ pulverizer models are designed for use of 7.60 x 15, 6 ply rib implement tir

5-1Chapter 5General Reference and SpecificationsTable 5-1: PDT Series 10’ - 14’PDT Series SpecificationsPDT-10 PDT-12 PDT-14Approximate Weight 1,828 l

ii4 Preventative MaintenanceFasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2 9J017GENERAL REFERENCE AND SPECIFICATIONSTable 5-2: PDT Series 16’ - 20’PDT Series SpecificationsPDT-16 PDT-18 PDT-20Approximate Weight 2,472 lbs.

GENERAL REFERENCE AND SPECIFICATIONS5-3Table 5-3: PXT Series 10’ - 14’PXT Series SpecificationsPXT-10 PXT-12 PXT-14Approximate Weight 2,157 lbs. (971

5-4 9J017GENERAL REFERENCE AND SPECIFICATIONSTable 5-4: PXT Series 16’ - 18’PXT Series SpecificationsPXT-16 PXT-18Approximate Weight 3,123 lbs. 1,405

GENERAL REFERENCE AND SPECIFICATIONS5-5Table 5-5: PDCT Series 10’ - 14’PDCT Series SpecificationsPDCT-10 PDCT-12 PDCT-14Approximate Weight 1,707 lbs.

5-6 9J017GENERAL REFERENCE AND SPECIFICATIONSTable 5-6: PDCT Series 16’ - 18’PDCT Series SpecificationsPDCT-16 PDCT-18Approximate Weight 2,496 lbs. (1

GENERAL REFERENCE AND SPECIFICATIONS5-7Table 5-7: POT Series 10’ - 15’POT Series SpecificationsPOT-10 POT-12 POT-14 POT-15Approximate Weight 2,052 lbs

5-8 9J017GENERAL REFERENCE AND SPECIFICATIONSTable 5-8: POT Series 16’ - 20’POT Series SpecificationsPOT-16 POT-17 POT-18 POT-20Approximate Weight 2,7

GENERAL REFERENCE AND SPECIFICATIONS5-9Table 5-9: PGT Series 10’ - 16’PGT Series SpecificationsPGT-10 PGT-12 PGT-14 PGT-16Approximate Weight 1,887 lbs

5-10 9J017GENERAL REFERENCE AND SPECIFICATIONSPage Intentionally Blank

Document Control Revision Log:Date Revision Improvement(s) Description and Comments11/2007 189rev1107 Updated Manual05/2012 189rev0512 Improved Drawin

1-1Chapter 1Introduction and Safety InformationIntroductionThe implement described in this manual has been designed with care and built by skilled wor

Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities.Trans

1-2 9J017INTRODUCTION AND SAFETY INFORMATIONNOTEInvestigation has shown that nearly 1/3 of all farm accidents are caused by careless use of machinery.

INTRODUCTION AND SAFETY INFORMATION1-3Maintenance Safety• Block the implement so it will not roll when working on or under it to prevent injury. • Do

1-4 9J017INTRODUCTION AND SAFETY INFORMATIONFigure 1-3: Safety DecalsWARNINGDO NOT GO NEAR LEAKSHigh pressure oil easily puncturesskin causing serious

INTRODUCTION AND SAFETY INFORMATION1-5Figure 1-4: Safety Decal Locations4K103“BRILLION”(FRONT & BACK)4K103“BRILLION”(FRONT & BACK)3K706528933R